Complete MoTeC M1 engine management kit for the 2026+ CF Moto Z10 turbo, with Beyond Redline firmware
Each kit is built to order. Lead time is confirmed when your order is placed.
Download the Data Sheet (PDF)
Overview
This kit replaces the factory CF Moto Z10 ECU with a fully programmable MoTeC M1 ECU. A plug & play jumper harness connects to the factory ECU connectors, so no factory wires are cut. The ECU comes with Beyond Redline's M1 Build firmware pre-loaded, written specifically for the turbo Z10. The factory dash, drive mode switch and start button keep working the way they do from the factory, and you get full control of fuel, ignition, boost and throttle.
Kit Options
- M130 Kit β $4,699.00
- M150 Kit β $5,499.00
What's Included
- MoTeC M1 ECU (M130 or M150, depending on the kit you choose)
- Beyond Redline M1 Build firmware for the CF Moto Z10, pre-loaded and licensed to the included ECU
- Plug & play jumper harness (factory ECU connectors to MoTeC M1)
- AEM 3-channel ignition coil driver
- Startup calibration
Optional Add-Ons
A wideband is highly recommended. These add-ons can be selected above. Choose either AEM X-Series option, or neither.
-
AEM X-Series inline wideband controller (30-0310) β $198.95: controller and sensor, no gauge. Sends air/fuel ratio straight to the ECU.
-
AEM X-Series wideband gauge (30-0300) β $206.95: same wideband with a 52 mm air/fuel gauge for the dash.
-
AiM infrared belt temperature sensor β $199.00 (requires the M150 kit, or a CAN expander on the M130): lets the drive belt protection act on belt temperature.
Factory Features That Keep Working
- Factory dash: RPM, gear, drive mode, boost gauge and coolant temperature
- Factory drive mode switch (Comfort / Trail / Sport), remembered between key cycles
- Factory push-button start, with normal ECU power-down after key off
- Factory gear position and vehicle speed
- Factory drive-by-wire throttle and blow-off valve
Performance and Protection Features
-
Boost control β controls the factory electronic wastegate with adjustable boost targets
-
Smooth throttle β adjustable throttle smoothing for each drive mode to take the jerk out of on/off throttle
-
Anti-lag β keeps the turbo spooled off throttle, with built-in temperature shutdowns and limits
-
Faster boost build β throttle spool feature to help bring boost in sooner
-
Launch control and adjustable rev limits
-
Drive belt protection β limits rpm under heavy load at low speed in High gear, or when belt temperature gets too high (optional belt temperature sensor; requires the M150 kit or a CAN expander on the M130)
-
Overboost protection β cuts fuel if boost goes past a safe limit
-
Cooling fan control β runs the fan on coolant temperature and can also use intake air temperature
-
Wideband support β works with AEM X-Series wideband controllers
-
Data logging β full MoTeC data logging and i2 analysis
Choosing an ECU: M130 or M150
Both kits run every feature listed above.
-
M130 β works, but has almost no room left for extra sensors or outputs. Adding the belt temperature sensor needs a CAN expander.
-
M150 β choose this if you plan to add sensors, gauges or other outputs later. It has room for add-ons like the optional belt temperature sensor, with no CAN expander needed.
Requirements and Notes
- Firmware is pre-loaded and licensed to the ECU in this kit. The license is not transferable to another ECU.
- Laptop with MoTeC M1 Tune for tuning and i2 for viewing logs.
-
Tuning support: Like any engine management system, the MoTeC M1 takes knowledge and experience to get the best results. We're happy to answer technical questions, but this kit does not include unlimited tuning support. We can quote tuning for your setup, refer you to a tuner in your area, or quote training if you'd like to tune it yourself.
-
Competition / off-road use only. This ECU kit is for closed-course competition and off-road vehicles only. It does not meet federal emissions requirements.
Compatibility
Questions? Contact Beyond Redline: 1-888-498-1223 Β |Β www.beyondredline.com